No images found.
A roller blind looks like the easiest load a gear motor will ever see: a few square meters of fabric on a tube, moving slowly, a couple of times a day. Most selection sheets treat it that way and quote a single torque figure. That is where the trouble starts, because the load at the first centimeter of travel is several times the load at the last, and the hardest requirement is not moving at all. The motor has to lift the blind from fully extended, hold it when the power is removed, and do both quietly enough to sit above a bed.

The Load Is Heaviest at the Start of the Travel
The fabric hangs from a tube, so the torque the motor must produce is the weight of the hanging fabric multiplied by the outside radius of the roll. Both terms change through the travel, and they change in opposite directions, which makes the arithmetic counter-intuitive.
At the bottom the whole blind hangs free. The weight is at its maximum and the roll is only the bare tube, so the radius is at its minimum. As the blind rises, fabric transfers onto the tube: weight falls in direct proportion to what is left hanging, while the radius grows only with the square root of the wound area. The weight term wins, so torque falls steadily from the moment the blind starts to climb.
Take a typical interior blind: 1.2 m wide, 2.5 m long, fabric at about 0.3 kg per square meter, wound on a 32 mm tube with 0.4 mm fabric. Fully extended, 8.8 N of fabric hangs from a roll of 16 mm radius, giving 0.141 N·m at the tube, or 1.44 kgf·cm. With 0.3 m still hanging, the weight is down to 1.1 N and the roll has grown to 23 mm, giving 0.025 N·m, or 0.25 kgf·cm. Same blind, same motor, one movement, and a factor of nearly six between the two ends.
The consequence is easy to miss. A blind that feels light at the top, where it moves fastest, may be at its limit at the bottom where it has to break the fabric free. Judging the motor by how the blind behaves once it is moving is judging it at the wrong point in the cycle.
Read the Rating at the Bottom, Not the Average
A ZGB37RG in its 12 V, 60 rpm build is rated at 2.0 kgf·cm and stalls at 3.6. Against the blind above, the requirement at the start of lift is 1.44 kgf·cm, which is 72 percent of the rating and 40 percent of the stall torque. That sounds comfortable until the allowances arrive: friction in the side channels, the stiffness of a blackout fabric coming off the roll, and a slightly out-of-square window all add torque the weight calculation does not contain.
Two consequences follow from the load falling through the travel. The first is that a blind sized on average torque will be marginal at the bottom and generous at the top, which is the opposite of what most selection sheets assume. The second is that a motor sized for the bottom is over-specified everywhere else, and the excess shows up as speed rather than as margin: the blind creeps away from the sill and accelerates as it rises, which reads as a control fault to anyone watching it.
Three ways out, and they are worth separating. Raising the reduction ratio trades output speed for torque, which suits a blind that only needs 20 to 30 rpm at the tube. Moving to a larger frame buys torque without slowing the output, at the cost of a headrail that has to be deeper. And a spring assist in the tube, common on heavier fabrics, offsets part of the hanging weight and flattens the whole curve, which is often cheaper than buying torque at the motor.
Holding Position Once the Power Is Off
The requirement that decides more designs than torque does is what happens when the motor stops. Fabric hanging from a tube exerts a continuous torque, and a permanent magnet DC gear motor with a spur or planetary gearbox has nothing to resist it once the supply is removed. The blind creeps down, slowly at first and faster as it unwinds and the hanging weight grows, the reverse of the lifting case, which is why a blind that lifts well can still drop overnight.
Three arrangements solve this, and they are not equivalent. A brake on the motor shaft holds mechanically and works regardless of gear type, at the cost of a wearing part and a little extra length. A worm gearbox holds by friction when the lead angle is small enough, which costs efficiency and needs verifying at the working temperature, since the friction doing the holding falls as the gearbox warms. An electronic brake, shorting the windings when the drive is disabled, produces holding torque proportional to speed: it resists a fast fall well and a slow creep poorly, the opposite of what a blind needs.
Whichever is chosen, the figure to specify is the torque the blind must hold when fully extended, not the torque needed to move it. Those are different numbers, and only the first one matters when a customer wakes up to a blind that has come down on its own.
What Quiet Actually Costs
A bedroom blind runs at night, a meter from someone’s head, so noise is a functional requirement rather than a nicety. The dominant source is not the motor but the mesh: the first gear stage turns fastest and its tooth meshing frequency sits in the band the ear is most sensitive to, which is why a well-made blind sounds like a soft hum and a cheap one like a small drill.
Three things move the number. Lower output speed lowers the meshing frequency and cuts annoyance twice over, through less energy and by moving the tone out of the most sensitive band. Metal gears cut to a finer pitch run quieter than moulded plastic at the same load, though plastic wins below a certain torque. And the mounting matters as much as the gearbox: a motor screwed rigidly to a hollow aluminum headrail turns that rail into a sounding board, so the same unit in a rubber-isolated cradle can measure several decibels lower.
For battery-powered blinds a fourth consideration has nothing to do with motion. A blind moving twice a day draws almost nothing while moving and a small standing current the rest of the time, and over a year the standing current dominates. A controller holding its radio awake at one milliamp will empty a cell pack long before the running current matters, which is why sleep current belongs on the specification beside the torque.

What to Send With the Enquiry
Five figures settle most of a blind design: the fabric weight per square meter, the maximum drop, the tube diameter, whether the blind must hold position without power, and the noise target with the distance it was measured at. With those, the load curve along the travel can be drawn and the rating checked at the right end of it.
The one figure worth insisting on is the holding torque at full extension. It is the requirement that eliminates candidate designs, it never appears on a catalogue page, and it is the one a customer discovers only after the first blind has fallen overnight. Send it with the rest, and the gearbox type, the reduction ratio and the frame size can be settled together rather than one at a time.
What Motor Does an Electric Roller Blind Need?
A roller blind looks like the easiest load a gear motor […]